How to Change Battery in SimpliSafe Glass Break Sensor

To replace the battery in a SimpliSafe glass break sensor, disarm your system, remove the sensor from its wall mount, open the casing with a small flathead screwdriver, swap out the old CR-123A lithium battery for a fresh one, and reassemble. The whole process takes most homeowners under ten minutes.

Your SimpliSafe glass break sensor does its job quietly. It sits on the wall, listens for the high-frequency sound of shattering glass, and—hopefully—never has to do much at all. Until the battery dies. Then, suddenly, that silent little device becomes a gap in your home’s security.

How to Change Battery in SimpliSafe Glass Break Sensor

The good news is that fixing it doesn’t require a technician, a ladder, or any particular skill set. What it does require is the right battery, a small screwdriver, and about ten minutes.

This guide on how to change battery in simplisafe glass break sensor walks you through every step: what you’ll need, how to open the sensor without cracking the housing, and what to watch for when you put it back together. There’s also a short section on the mistakes people make most often—because a few of them are less obvious than you’d think.

Understanding the SimpliSafe Glass Break Sensor

The glass break sensor is a compact, wall-mounted device that communicates wirelessly with your SimpliSafe base station. It’s designed to detect the sound of breaking glass from up to 20 feet away—a range that covers most standard-sized rooms.

Because it runs entirely on battery power, everything it does depends on battery health. A sensor with a depleted battery may appear online in your app while actually being unresponsive. That gap between perception and reality is worth taking seriously.

SimpliSafe glass break sensors run on a single CR-123A lithium battery. Under typical conditions, that battery may last anywhere from three to five years—though factors like temperature, how often the sensor fires, and sensitivity settings can shorten that window. When the battery starts to drain, your SimpliSafe app will notify you. The moment you see that alert, it’s worth acting on it sooner rather than later.

Tools and Materials Needed

You don’t need much here. Before you start, gather the following:

A Fresh CR-123A Lithium Battery
This is the only battery type compatible with the SimpliSafe glass break sensor. CR-123A batteries are available at most hardware stores and electronics retailers, as well as online. It’s worth spending a little more on a reputable brand—budget alternatives tend to drain faster and don’t always perform consistently at lower temperatures.

A Small Flathead Screwdriver
A jeweler’s screwdriver or a thin, flat-tipped tool works best. The goal is to gently pry open the sensor casing without scratching or cracking the plastic, so avoid anything too thick or sharp.

To Replace the Battery in a
 Simplisafe Glass Break Sensor

A Soft Cloth or Paper Towel
Useful for handling the battery without transferring oils from your fingers, and for wiping the sensor down if it’s collected dust.

Your SimpliSafe App or Keypad
Keep it nearby. You’ll want to confirm the sensor reconnects properly once the battery is replaced.

7 Simple Steps on How to Change Battery in SimpliSafe Glass Break Sensor

Step 1: Disarm Your SimpliSafe System

Start here, not at the sensor. Open your SimpliSafe app or go to your keypad and disarm the system entirely. Enter your PIN and switch to “Off” or “Home” mode. Skipping this step risks triggering a false alarm—and possibly a call from your monitoring center.

Step 2: Locate the Glass Break Sensor

These sensors are typically mounted high on walls or tucked into room corners near large windows. Before you remove it, take a moment to note its exact position and angle. Getting the remount right later is easier when you haven’t forgotten how it was sitting.

Step 3: Remove the Sensor from the Wall Mount

SimpliSafe glass break sensors attach to a wall bracket through a twist or clip mechanism, depending on the model. Either rotate the sensor counterclockwise or press the release tab to detach it. Go slowly—the sensor is light, but dropping it onto a hard floor isn’t ideal.

Step 4: Open the Sensor Casing

Look along the edge of the sensor for a small seam or notch. Insert your flathead screwdriver into that gap and apply gentle, steady pressure. Work around the edge if the cover doesn’t pop immediately. There’s no need to force it. The two halves should separate cleanly.

Step 5: Remove the Old Battery

With the casing open, you’ll see the CR-123A battery seated in a small compartment. Before pulling it out, note which end is positive and which is negative—the housing typically has markings, but it’s easy to forget in the moment. Slide or lift the old battery out. If it’s been in place for a few years, it may be snug; the edge of a fingernail or screwdriver can help ease it free.

The Glass Break
 Sensor is a Compact

Step 6: Insert the New Battery

Match the orientation of the new battery to the markings inside the compartment—typically a small + and – symbol. Press it firmly into place. If possible, handle the battery with a cloth rather than bare fingers to keep the terminals clean.

Step 7: Reassemble and Test the Sensor

Snap the two halves of the casing back together, checking that they align evenly before pressing them closed. Reattach the sensor to its wall mount using the reverse of the removal process. Then open your SimpliSafe app or check your keypad—within a few minutes, the sensor should appear online, and the low-battery alert should clear.

If the alert doesn’t clear after five minutes, try manually refreshing your device list in the app. Following these steps on how to change battery in simplisafe glass break sensor will ensure that your home security system stays functioning properly and you can have peace of mind knowing that your glass break sensor is working efficiently.

Common Mistakes to Avoid

Most battery replacement issues come down to two things: using the wrong battery or rushing the reassembly.

The most common mistake is substituting a standard AA or AAA battery. They won’t fit, and even if somehow forced into place, they’re not compatible with the sensor’s power requirements. A closely related issue is inserting the correct battery in the wrong orientation. A reversed CR-123A won’t power the sensor and, over time, could cause damage to the contacts. Always double-check polarity before closing the casing.

Reassembly is where things can also go wrong quietly. If the two halves aren’t seated properly, the casing may appear closed while leaving a small gap—which affects the sensor’s performance and can cause intermittent disconnects. Press firmly and listen for the click before remounting.

One more thing worth mentioning: don’t skip the final app check. Confirming the sensor is online takes thirty seconds and tells you immediately if something went wrong during the process.

Do You Need Professional Help?

For most homeowners, this is a confident DIY task. No wiring, no configuration, no special knowledge—just a screwdriver and the right battery.

Look Along the 
Edge of the Sensor

That said, there are situations where reaching out makes sense. If the sensor isn’t reconnecting to the base station after a fresh battery is installed, or if the housing is visibly cracked or damaged, SimpliSafe’s customer support team can walk you through advanced troubleshooting or arrange a replacement. SimpliSafe offers 24/7 support, so the option is there if you need it.

Frequently Asked Questions

How Do I Know When My SimpliSafe Glass Break Sensor Battery Needs Replacing?

Your SimpliSafe app will send a push notification when the battery is running low. You can also check manually by navigating to the “Devices” section of your SimpliSafe dashboard. Checking sensor health every few months—even without an alert—may help you catch a draining battery before it becomes a problem.

What Type of Battery Does the SimpliSafe Glass Break Sensor Use?

The SimpliSafe glass break sensor uses a CR-123A lithium battery. This battery type is available at most hardware stores, electronics retailers, and online. Opting for a quality lithium battery appears to offer better performance and a longer lifespan than generic alternatives.

Will Replacing the Battery Reset My Sensor’s Settings?

No. Replacing the battery does not reset or alter the sensor’s configuration. Once the new battery is in and the sensor is remounted, it will reconnect to the SimpliSafe base station automatically and resume normal operation with all previous settings intact.

How Long Does a CR-123A Battery Last in a SimpliSafe Glass Break Sensor?

Most Battery Replacement
 Issues Come Down

Under typical conditions, a CR-123A lithium battery may last between three and five years. Factors like temperature fluctuations, sensor sensitivity settings, and how frequently the sensor triggers alerts could shorten that range.

What Should I Do If the Sensor Won’t Reconnect After a Battery Change?

First, confirm the battery is seated correctly and the casing is fully closed. If the sensor still doesn’t appear online, try removing and reinserting the battery. You can also try restarting your SimpliSafe base station. If none of those steps work, contact SimpliSafe support directly—they offer 24/7 assistance and can help diagnose whether the issue is with the sensor itself.

Keep Your Sensor—and Your System—Running Smoothly

Replacing the battery in a SimpliSafe glass break sensor is one of those maintenance tasks that takes longer to think about than to actually do. With the right battery on hand and the seven steps above, most homeowners can complete it in under ten minutes.

The bigger point is this: a sensor with a dead battery is functionally the same as no sensor at all. Staying on top of low-battery alerts—and keeping a spare CR-123A somewhere accessible—means your SimpliSafe system keeps doing what it’s supposed to do, quietly and reliably, in the background. Thanks for reading this guide on how to change battery in simplisafe glass break sensor.

Leave a Comment